Panasonic KX-TVP50E Installation Manual Download Page 145

Page: 145 / 368

SYSTEM MAINTENANCE AND TROUBLESHOOTING

Installation Manual

145

7.4

TROUBLESHOOTING GUIDE

Table 30

PROBLEM

PROBABLE CAUSE

POSSIBLE SOLUTION

Nothing is heard from the
VPS when accessing the VPS.

•

Improper connection of jacks.

•

Bad connection with PBX.

•

Confirm that you are using the
correct extension number for
the VPS. Ask your System
Administrator.

•

Check if the jacks of the VPS
are connected to the proper
jacks of the PBX (see
1.4

DIGITAL

INTEGRATION).

•

Check the System Programme
[130] of the KX-TA series
telephone systems to see if the
programming agrees with the
actual connection.

•

Check the System Programme
[117] of KX-TD series
telephone systems to see if the
programming agrees with the
actual connection.

Unable to utilize some of the
DPT Integration features,
even though DPT Integration
has been established properly.

•

Your PBX cannot support the
feature.

•

The software version of your
PBX is lower than required.

•

Consult your dealer.

The VPS does not operate.

•

Bad printed circuit board.

•

Bad connection with PBX.

•

Incomplete card insertion.

•

Change the printed circuit
board.

•

Check the connection between
the VPS and PBX.

•

Insert the card firmly into the
card slot.

Dialling is not registered.

•

A pulse phone is being used by
mistake.

•

Improper setting of integration
mode.

•

Change to a touch tone phone.

•

Adjust the integration mode
properly between the VPS and
your PBX (see "Integration
Mode" in Table 71 in
B7.3

PBX Interface

Parameters).

Summary of Contents for KX-TVP50E

















































































































































































































































































































































































Search results

Summary of Contents for KX-TVP50E

Reviews:

Related manuals for KX-TVP50E

Brands by name

Popular brands

Panasonic KX-TVP50E, Installation Manual

Search results

Summary of Contents for KX-TVP50E

Reviews:

Related manuals for KX-TVP50E

Brands by name

Popular brands