manualshive.com logo in svg

Panasonic KX-TVP50E, Installation Manual

Share
Download
Panasonic KX-TVP50E Installation Manual Download Page 6

Precaution

6

Installation Manual

Precaution

This appliance is supplied with a moulded three pin mains plug for your safety and 
convenience. A 5 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 
amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark

 

 

or the BSI mark

 

 

on the body of the fuse.

If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is 
replaced. If you lose the fuse cover the plug must not be used until a replacement cover is 
obtained.
A replacement fuse cover can be purchased from your local Panasonic Dealer.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN 
YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND 
DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE 
CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.

If a new plug is to be fitted please observe the wiring code as shown below.
If in any doubt please consult a qualified electrician.

WARNING

THIS APPLIANCE MUST BE EARTHED

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:

Green-and-Yellow :

Earth

Blue :

 Neutral

Brown :

 Live

As the colours of the wire in the mains lead of this appliance may not correspond with the 
coloured markings identifying the terminals in your plug, proceed as follows.

The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the 

plug which is marked with the letter E or by the Earth symbol

 

 

or coloured GREEN or 

GREEN-AND-YELLOW.

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT
CAREFULLY.

Summary of Contents for KX-TVP50E

















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands