Panasonic KX-TVP50E Installation Manual Download Page 3 | Manualshive

Page: 3 / 368

background image

Important Information

Installation Manual

3

Important Information

SAFETY REQUIREMENTS

•

Read all the information contained in this manual.

•

Follow all product warnings, cautions, and instructions.

•

Install the unit so that the power cord is not obstructed in any way. Do not connect this unit
to an extension cord.

•

Mount the unit on a stable wall surface. Do not mount the VPS inside of a separate
enclosure unless it is properly ventilated.

•

Keep the unit free of dust, moisture, condensation, high temperature exposure (more than
40 °C) and vibration. Do not expose the unit to direct sunlight.

•

This unit is designed to operate at one specific voltage and current setting. The proper
voltage and current required for this unit are listed on the product label.

•

This unit is equipped with a 3-wire earth plug. The plug will only fit into a earth power
outlet. Do not modify this plug in any way. If it cannot be inserted into the outlet, have the
outlet replaced by a licensed electrician.

•

If the unit malfunctions, disconnect the unit from the telephone line and check the line by
reconnecting the telephone. If the telephone operates properly, have the VPS repaired by a
qualified service technician.

•

Unplug the unit from its power source before cleaning.

•

Handle the unit carefully. Do not drop or otherwise expose the unit to physical shock.

•

Unplug and transport the unit to a service technician if the power supply cord is frayed or
damaged, if the cabinet is cracked or broken, or when the unit has been exposed to moisture,
has been dropped, or is not otherwise operating properly.

•

Do not install the unit near water or moisture, heating appliances, or electrical noise
generating devices such as televisions, monitors, fluorescent lamps, or electric motors.

•

Do not insert wires, pins, or any other material into the unit's vent slots or access points.
This could result in electrical shock and serious unit malfunction.

•

Do not block the vent slots and openings located on the front and top of the unit.

•

Do not overload wall outlets. Overloaded outlets could result in fire and/or electrical shock.

•

Do not disassemble this product. Dangerous electrical shock could result. The unit must
only be disassembled and repaired by qualified service technicians.

•

Do not use solvents, liquid cleaners, water, or abrasive powders to clean this unit. Use only
a damp soft cloth for cleaning.

•

Do not use the telephone during a lightning storm or to report a gas leak in the vicinity of
the leak.

WARNING

TO PREVENT FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.

«
1
2
3
4
5
...
»

Summary of Contents for KX-TVP50E

















































































































































































































































































































































































Reviews:

No comments

Related manuals for KX-TVP50E

Brand: DAPU Pages: 4

Brand: Samsung Pages: 2

Brand: Barracuda Pages: 3

Event Master E2

Brand: Barco Pages: 2

Brand: Barco Pages: 7

Brand: Barco Pages: 7

Brand: Tailfin Pages: 8

Brand: Yakima Pages: 11

Brand: BAFANG Pages: 4

Brand: UNIT 1 Pages: 23

Brand: Kabuto Pages: 16

Brand: Valcom Pages: 1

Brand: Valcom Pages: 13

Brand: Kabuto Pages: 12

Brand: Olympia Pages: 28

Brand: Swann Pages: 12

Brand: Satlink Pages: 16

Brand: Hama Pages: 138

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands