Panasonic EBL512 G3 5000 Planning Manual Download

Page: 40 / 168

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

The following units can be connected to the COM loops (in

NORMAL

mode):

NOTE!

The

Alarm Acknowledge Facility Control (AAFC)

is used on the

Australian market only.
The

I/O Unit for Fan control (3361)

is normally used with the Fan

control panel 4593 only.
The

MCP Addressable Manual Call Point with Isolator 4333

is a future

product under construction, i.e. cannot be used today.

Obsolete units

(listed below) can be found in old installations and can

be used in EBL512 G3 installations as well.

NOTE!

When one or more of the

Obsolete units

listed above are used on a

COM loop, the maximum number of loop units is 127, i.e. only
technical address

1-127

can be used.

Address setting

Each  COM  loop  unit  has  to  have  a  unique  COM  loop  address  (001-
255).  This address and the mode are set with an Address Setting Tool
(3314).    For

EBL512 G3

is always the

NORMAL

mode used

(default).

Summary of Contents for EBL512 G3 5000









































































































































































Search results

Summary of Contents for EBL512 G3 5000

Reviews:

Related manuals for EBL512 G3 5000

Brands by name

Popular brands

Panasonic EBL512 G3 5000, Planning Manual

Search results

Summary of Contents for EBL512 G3 5000

Reviews:

Related manuals for EBL512 G3 5000

Brands by name

Popular brands