Panasonic EBL512 G3 5000 Planning Manual Download Page 135 | Manualshive

Page: 135 / 168

background image

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

133

20.1.3.5

Alarm delay time (seconds)

Valid for the detectors and zone line inputs with this option selected
via WinG3

120

.

0 is default. 0-255 seconds is possible. Note, this delay time starts
when the fire alarm normally should have been activated.

20.1.4

System properties, Page 2



Latch Faults

(default): All faults have to be acknowledged, also

corrected faults.

Checkbox  not  marked  =  No  fault  latching  =  Not  corrected  faults
have  to  be  acknowledged  but  corrected  faults  will  automatically
be deleted from the fault list.



Global reset of Fan Controls Outputs

: Reset of fan control

system is

global

, i.e. all fan control systems in the EBL512 G3

system will be reset. (Regarding Fan control, see page 31.)
Checkbox not marked = Reset of fan control systems is

local

, i.e.

all fan control systems in the c.i.e. where the switch is located will
be reset.



Use Daylight Saving

:

Australian convention: Forward 1 hour the first Sunday in
October, 02:00



03:00. Backward 1 hour the first Sunday in

April, 03:00



02:00.

New Zealand convention: Forward 1 hour the last Sunday in
September, 02:00



03:00. Backward 1 hour the first Sunday in

April, 03:00



02:00.

All other conventions: According to the current EU regulations,
i.e. forward 1 hour the last Sunday in March, 02:00



03:00.

Backward 1 hour the last Sunday in October, 03:00



02:00.

Checkbox not marked = Daylight saving time is not used.



Silence Switch Disables Alarm Devices

: New Zealand function.

See page 117.



Silence Buzzer With Door Switch

: If the buzzer in the c.i.e.

shall be silenced when the door is opened, this checkbox shall be
marked. This is a violation to the EN54-2 standard.



Flash LED on MCP

: The manual call point (type 3333 / 3339)

built-in LED will flash to indicate communication with the c.i.e.
Checkbox not marked = This option is disabled, i.e. the LED is
switched off until the call point is operated.



Redundant TLON Network

: This checkbox shall be marked

when two TLON Networks shall be used, i.e. each control unit in
the system is equipped with two TLON connection boards (1590).
See also chapter "TLON connection board 1590", page 36.

120

Regarding the Australian and New Zealand conventions the "Alarm

Verification Facility" is valid, see page 101.

«
...
133
134
135
136
137
...
»

Summary of Contents for EBL512 G3 5000









































































































































































Reviews:

No comments

Related manuals for EBL512 G3 5000

Brand: Canon Pages: 2

Brand: NEC Pages: 146

Brand: Haldex Pages: 8

Brand: Oceanic Pages: 11

Brand: Trane Pages: 72

Brand: Znshine Solar Pages: 16

Phase Matrix PXI-1420

Brand: National Instruments Pages: 38

Brand: WAGO Pages: 134

Brand: GAC Pages: 9

Brand: ALLEN & HEATH Pages: 15

Entelli-Switch 250

Brand: GE Pages: 32

Brand: AC Tech Pages: 2

Brand: V-TAC Pages: 2

Brand: Diamond Systems Pages: 15

RC Electronic DPSI LCD

Brand: Emcotec Pages: 32

Brand: Allen-Bradley Pages: 88

Brand: Grundfos Pages: 12

Apollo 70-600 Series

Brand: Conbraco Industries Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands