Panasonic EBL512 G3 5000 Planning Manual Download Page 50 | Manualshive

Page: 50 / 168

background image

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

48

technical address can be written.

The Address setting tool (3314) is also used for mode setting:

NORMAL mode

: Used for 3364 in system EBL512 G3.

2330 mode

: Not used in system EBL512 G3.

2312 mode

: Not used in system EBL512 G3.

NOTE!

See also chapter "Limitations", page 160.

9.1.3

Alarm devices (addressable sounders)

3377

Addressable siren.  The siren is connected to a COM loop.  It is
power supplied  via the  COM  loop, i.e. the  number  of  sirens  is
depending  on  the type  and  number  of  other  units  connected  to
the COM loop.

37

Red ABS plastic housing. Three sound types

(tones) and three priority levels are available. For each level an
output control expression and a sound type is programmed (via
WinG3). For more technical data, see the Product Leaflet.

The COM loop address is set with the Address setting tool
(3314).

The Address setting tool (3314) is also used for mode setting:

NORMAL mode

: Used for 3377 in system EBL512 G3.

2330 mode

: Not used in system EBL512 G3.

2312 mode

: Not used in system EBL512 G3.

NOTE!

See also chapter "Limitations", page 160.

3379

Addressable sounder base.

38

3379 consists of an analog base

(3312)  mounted  together  with  a  sounder.    3379  is  mounted  in
the  ceiling.    An  analog  detector  can  be  plugged  in  the  base,
which has screw terminals for  the COM loop and an  ext. LED
(2218).    Prepared  for  mechanical  lock  of  the  detector  -  if
required.    Recess  for  label  holder  (3391).    3379  is  power
supplied via the COM loop, i.e. the number of sounder bases is
depending  on  the type  and  number  of  other  units  connected  to
the  COM  loop

37

. Three sound types (tones) and three priority

levels are available. For each level an output control expression
and a sound type is programmed (via WinG3). For more
technical data, see the Product Leaflet.

The  COM  loop  address  is  set  with  the  Address  setting  tool
(3314). The unit has an address label on which the programmed
COM  loop  address  can  be  written.    (The  detector  has  its  own
COM loop address set via the Address setting tool 3314.)
The Address setting tool 3314 is also used for mode setting:

NORMAL mode

: Used for 3379 in system EBL512 G3.

2330 mode

: Not used in system EBL512 G3.

2312 mode

: Not used in system EBL512 G3.

NOTE!

See also chapter "Limitations", page 160.

4380

Addressable beacon.

40

The LED beacon is connected to a COM

loop. It is power supplied via the COM loop, i.e. the number of
beacons is depending on the type and number of other units

37

The number of 3377 + 3379 units must be < 50.

38

This unit has replaced the Sounder base 3378.

«
...
48
49
50
51
52
...
»

Summary of Contents for EBL512 G3 5000









































































































































































Reviews:

No comments

Related manuals for EBL512 G3 5000

Brand: ABB Pages: 30

Brand: ABB Pages: 15

Brand: ABB Pages: 10

Brand: ABB Pages: 44

Brand: NCR Pages: 6

AirGENIO SUPERIOR

Brand: 2VV Pages: 27

Brand: EasyIO Pages: 12

Brand: RMG Pages: 6

Brand: Bartlett Pages: 5

Brand: Camozzi Pages: 33

Brand: Camozzi Pages: 2

Brand: Camozzi Pages: 64

Brand: Campbell Pages: 3

Brand: jcm-tech Pages: 8

Brand: Laird Pages: 38

Brand: Laird Pages: 5

Brand: KaRo Pages: 12

Brand: Vacon Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands