Panasonic EBL512 G3 5000 Planning Manual Download Page 58 | Manualshive

Page: 58 / 168

background image

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

56

get access to the push buttons.  They are disabled until they are
supposed  to  be  used.    The  unit  shall  be  wall  mounted.    Two
compression glands are attached.  In all other respects it is like
1826, except that a printer cannot be mounted in 1828.

The unit shall run in

S/W mode 1826/28 – 1587

. Up to 1200 m

cable can be used. For more information, see Technical
description MEW00249.

1835

Printer. Can be mounted in the External Fire Brigade Panel

1826

. It will print all the alarms, including the alarm texts.

Note that the printer current consumption is up to 200 mA when
printing.

9.2.2

Alert Annunciation Units

When the

A

lert

A

nnunciation (

AA

) function shall be used in system

EBL512 G3, a unit is required for the related manoeuvres, i.e. to
acknowledge / reset the

AA

alarms. For a detailed description of the

Alert Annunciation function, see chapter "Alert Annunciation", page
102.

1735

Alert  Annunciation  Unit  (AAU).    A  compact  size  enclosure
(HxWxD, 145 x 220 x 50 mm) made of grey high impact ABS.
Fitted  with  a  supplementary  "O"  ring  gasket,  it  will  comply
with  IP61,  in  respect  of  dust  and  moisture.    The  unit  has  no
door, i.e. the front is accessed directly but the push buttons are
disabled until they  are  supposed to  be  used.   The  unit  shall  be
wall  mounted.    Two  compression  glands  are  attached.

The

front's designation texts are in Swedish.

All  or  selected  fire  alarms  will  be  presented  in  a  display
(alphanumeric  LCD,  2x40  characters),  with  back-light.    An
alarm  text  will  also  be  presented  together  with  each  alarm,  if
programmed  in  EBL512  G3.    Furthermore,  at  least  617  texts
can for selected fire alarms be stored in the unit and will in such
a case be shown, instead of the texts sent out from EBL512 G3
for  these  alarms.    These  text  messages  will  be  downloaded  to
the  unit  via  EBL512  G3.    A  built-in  buzzer  will  sound  to
indicate a not acknowledged

AA

alarm.

New software versions can be downloaded directly in the unit.
The unit is power supplied from EBL512 G3 or an external
power supply.

The unit has the following LEDs:

Fire

and

Alarms queued

, indicating fire /

AA

alarm.

Operation

, indicating that the unit is in operation, i.e. the

AA

function is enabled in the system. A time channel can be used
to enable the

AA

function.

«
...
56
57
58
59
60
...
»

Summary of Contents for EBL512 G3 5000









































































































































































Reviews:

No comments

Related manuals for EBL512 G3 5000

Brand: Fancom Pages: 31

Brand: 3M Pages: 90

Brand: Federal Signal Corporation Pages: 79

Brand: Federal Signal Corporation Pages: 32

Brand: Garmin Pages: 220

Brand: Gardena Pages: 16

Brand: Ziton Pages: 28

Brand: Unico Pages: 164

Brand: DANIEL Pages: 48

Brand: Watlow Pages: 20

CIATControl OPC Server

Brand: CIAT Pages: 32

Brand: Danfoss Pages: 8

Infi 90 IMAOM01

Brand: Bailey Pages: 44

Brand: Woodward Pages: 32

Universal Family for Sony

Brand: Jolly Pages: 68

DMC-40x0 Series

Brand: Galil Motion Control Pages: 280

Brand: Anritsu Pages: 54

Brand: Governors America Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands