Panasonic EBL512 G3 5000 Planning Manual Download Page 110 | Manualshive

Page: 110 / 168

background image

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

108

shall not be selected, see chapter "System properties, Page 2", page
133.

NOTE!

Enhanced Disablement is NOT valid when a time channel is

used for disablements, only when menu H2/B1 or B2 is used.

16.16.1

Disable zone

A whole zone (all addresses within a zone, except the manual call
points) can be disabled via menu H2/B1. Re-enabled via menu
H2/B4.

16.16.2

Disable zone / address

Individual alarm points can be disabled via menu H2/B2. Re-enabled
via menu H2/B5.
Time channels can be used to disable and re-enable automatically.

16.16.3

Disable control output

All outputs (except outputs of type "Alarm Device") can be
individually disabled via menu H2/B3. Re-enabled via menu H2/B6.
Disabled output will stay in (or return to) the normal condition for the
output respectively.

16.16.4

Disable / Re-enable output type

The control outputs can be collective disabled via menu H2/B7, type:
"Control (general)"
"Extinguishing"

"Ventilation"

"Control/exting./vent.
"Interlocking"

It is possible to do this for one or more specific control units or for all
control units (i.e. the whole system). Re-enabled via menu H2/B7.
Disabled outputs will stay in (or return to) the normal condition for the
output respectively.

16.16.5

Disable / Re-enable alarm devices

The  control  outputs  of  type  "Alarm  device  (sounder)"  can  be
collective disabled via menu H2/B8.  It is only possible to do this for
all control units (i.e. the whole system).  Re-enabled via menu H2/B8.
Disabled outputs will stay in (or return to) the normal condition for the
output respectively.

16.17

Disable interlocking output

Individually disabled via menu H9/C4. Re-enabled via menu H9/C5.
See also chapter "Disable interlocking output (H9/C4)", page 87.

16.18

Disable outputs for routing equipment

Disabled and Re-enabled via menu H2/B9. For more information see
EBL512 G3 Operating Instructions MEW01163.

«
...
108
109
110
111
112
...
»

Summary of Contents for EBL512 G3 5000









































































































































































Reviews:

No comments

Related manuals for EBL512 G3 5000

Brand: Ubisys Pages: 2

Brand: Bang & Olufsen Pages: 36

Brand: Mad Catz Pages: 4

Brand: Kasco Pages: 3

Brand: vacuubrand Pages: 12

Brand: Vacon Pages: 47

Brand: Vacon Pages: 40

Brand: Klimaire Pages: 5

Brand: Nordelettronica Pages: 8

Brand: Rational Pages: 140

Brand: SILENTRON Pages: 20

Brand: MacroAir Technologies Pages: 32

RSF-B mini Series

Brand: Harmonic Drive Pages: 32

Brand: Pilz Pages: 32

Brand: CALEFFI Pages: 10

EZ-ZONE PM L AAAAB Series

Brand: Watlow Pages: 30

8040 CNC - FEATURES

Brand: Fagor Pages: 247

Brand: Yale Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands