Panasonic EBL512 G3 5000 Planning Manual Download Page 134 | Manualshive

Page: 134 / 168

background image

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

132

20.1.3.2

Alarm Acknowledgement Facility

Used in conjunction with the AAF Control that is available on the
Australian market only.

See also chapter "Alarm Acknowledgement Facility (AAF)", page
104.

Investigation period (IP) time

: 3

min.

3 is default. 1-3 is possible.

Acknowledge period (AP) time

: 60

sec.

60 is default. 10-60 is possible.

20.1.3.3

Disable routing equipment by door switch

Valid for the following control unit outputs for routing equipment:

Fire alarm

(for Fire brigade tx)

Fault condition

(for Fault tx)



None

(default): Door open in a C.U. or an ext. FBP will

not

disable these outputs.



Any control unit door

: Door open in any C.U. will disable these

outputs in all C.U:s.



Any door

: Door open in any C.U. or any ext. FBP will disable

these outputs in all C.U:s.

In the display (or via menu H4/U1) is shown (xx = C.U. number):

Fire alarm routing disabled (by open door in
CU xx)

20.1.3.4

Alarm reset method

One of the following alternatives shall be selected.



All

(default): All fire alarms in the system will be reset

simultaneously by pressing the "Reset" button (on the c.i.e. front)
once.



Single

: One fire alarm in the system, i.e. the fire alarm shown in

the field in the middle of the control unit display will be reset by
pressing the "Reset" button once. Any other fire alarm has to be
reset the same way, one by one.
This function is a violation to the EN54-2 standard.



Single With Automatic Disablement

: Like "Single" reset but

with the Disablement function (see below) as well.
This function is a violation to the EN54-2 standard.

Disablement function: If an alarm point or zone is reset while it still is
in alarm state (e.g. smoke in a smoke detector or a manual call point
with a broken glass) this unit will be automatically disabled in order to
not activate a new fire alarm within 20 seconds. It will stay disabled
until re-enabled via menu H2/B5.

LED

Fault / Disablements

"General disablements" on the c.i.e. front

is indicating one or more disablement in the system.

«
...
132
133
134
135
136
...
»

Summary of Contents for EBL512 G3 5000









































































































































































Reviews:

No comments

Related manuals for EBL512 G3 5000

Brand: CALEFFI Pages: 12

QuickSetter+ 132 Series

Brand: CALEFFI Pages: 5

Brand: Watts Pages: 4

Brand: WaterCop Pages: 4

Brand: TEL Pages: 26

Brand: Vimar Pages: 32

Brand: D+H Pages: 2

Brand: K+R Performance Engineering Pages: 12

Brand: M-Elec Pages: 2

ACTPRO PRODUCT RANGE

Brand: ACT Pages: 8

Brand: Jebao Pages: 4

Brand: ACE RC Pages: 24

Brand: Fisher Pages: 44

Brand: OneRemote Pages: 3

Brand: Freescale Semiconductor Pages: 41

Brand: RAK Pages: 64

Brand: Lafayette Pages: 11

Brand: Walchem Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands