Panasonic EBL512 G3 5000 Planning Manual Download Page 107

Page: 107 / 168

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

105

Quiscent state

AP timer starts

Count down

AAFC

button

pressed?

AP time

remains?

Yes

IP timer starts

Buzzer ON
Detector LED ON
AAFC LED ON

Buzzer OFF

All detectors

normal?

Count down

IP time

remains?

Yes

Fire Alarm

in the C.I.E.

Any detector

in alarm?

Yes

Detector LED OFF
AAFC LED OFF

AAFC LED OFF

Figure 23. Alarm Acknowledgement Facility (AAF) flow chart.

During the AAF Process, an AAF alarm will be indicated in the c.i.e.
display ….

…. during the

cknowledgement

eriod (

Period):

AAF zone xx, activated

…. during the

nvestigation

eriod (

Period):

AAF zone xx, investigation in progress

The AAF zone xx (xx=00-99) is only valid for the c.i.e. it is shown in,
i.e. not for the whole system.

If more than one AAF zones have been activated only the first is
shown in the display.

NOTE!

All devices belonging to an AAF zone must be connected to one c.i.e.

Summary of Contents for EBL512 G3 5000









































































































































































Search results

Summary of Contents for EBL512 G3 5000

Reviews:

Related manuals for EBL512 G3 5000

Brands by name

Popular brands

Panasonic EBL512 G3 5000, Planning Manual

Search results

Summary of Contents for EBL512 G3 5000

Reviews:

Related manuals for EBL512 G3 5000

Brands by name

Popular brands