Panasonic EBL512 G3 5000 Planning Manual Download Page 111 | Manualshive

Page: 111 / 168

background image

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

109

16.19

Disconnect & Re-connect loop / zone line
input

Disconnected via menu H8/S1 and Re-connected via menu H8/S2:

COM loop
Zone line input

Addr. zone interface (3361 zone line input)

For more information see EBL512 G3 Operating Instructions
MEW01163.

16.20

External time channels 15-63

External time channels can be used to:



disable and re-enable alarm points



turn the Alert Annunciation function on/off



activate programmable control outputs



turn Alternative alarm algorithm for analog detector types 430x
on/off



turn the 2-unit dependence function on/off

The  external  time  channels  15-63  are  for  the  whole  system.    One
programmable  input  with  trigger  condition/type  "External  Time
Channel" is used for each external time channel, which also is given a
"Name".    The  input  is  controlled  by  some  external  equipment,  e.g.
another time system, a key switch, a timer, etc. with a normally open
contact (normally low)  or a normally closed contact (normally high).
When the input is "activated" the time channel is ON.

NOTE!

You must not use more than one input per time channel.

(This is checked in the "Validity check" in WinG3).

16.21

Test mode

Up  to  four  zones  can  be  set  in  Test  mode  at  the  same  time.    Alarm
points /  zones  can  be tested  during  the Monthly  test  via  menu  H1  or
separately  via  menu  H7.    For  more  information  see  EBL512  G3
Operating  Instructions  MEW01163.    The  LED  "Test  mode"  on  the
c.i.e. front  indicates one or more zones in  Test mode.  Zones in Test
mode  are  also  simultaneously  shown  in  the  c.i.e.  display.
Disablements,  faults  and  fire  alarms  have  higher  priority,  i.e.  the
presentation  of  zones  in Test  mode  will  be  suppressed  during  such  a
condition.  In order to shorten the testing time, any time delay before
alarm will be "turned off" in Test mode.

102

16.22

Test alarm devices

The programmable outputs of type "Alarm device" can be collectively
activated via menu H8/S5, which make it possible to test the alarm

102

The test mode alarm will be activated at the pre-warning level. Any 2-

zone / -address dependence and the function "delayed alarm" will be ignored.

«
...
109
110
111
112
113
...
»

Summary of Contents for EBL512 G3 5000









































































































































































Reviews:

No comments

Related manuals for EBL512 G3 5000

Brand: 3M Pages: 34

Brand: Abicor Binzel Pages: 8

Brand: NAD Pages: 4

Brand: NAD Pages: 4

Brand: Paradox Pages: 6

Brand: 2gig Technologies Pages: 6

Brand: DeLaval Pages: 102

Brand: CAME Pages: 128

Comfort System Z-300-HC

Brand: Jackson Systems Pages: 2

SUPERSEAL 2014 Series

Brand: APV Pages: 20

Brand: LEYBOLD Pages: 12

Brand: Hach Pages: 504

ECOFRIDGE DISPLAY

Brand: HULTSTEINS Pages: 16

Brand: Teracom Pages: 8

Brand: AXIOMTEK Pages: 2

Brand: Davey Pages: 8

Neon 2000 Family

Brand: UniData Communication Systems Pages: 23

Brand: salmson Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands