Panasonic EBL512 G3 5000 Planning Manual Download | Manualshive

Page: 52 / 168

background image

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

50

4313

no. 00

4313

no. 01

no. A

no. B

Segment A

Segment B

Segment C

EBL512 G3

A-dir.



B-dir.



Figure  9.    Two  4313  isolators  connected  to  a  COM  loop  gives
three  loop  segments,  i.e.  Segment  A  (A-00),  B  (00-01)  and  C
(01-B).    If  more  isolators  have  to  be  added,  the  sequence
numbers have to be updated (via WinG3), e.g. if one isolator is
put in between isolator no. 00 and no. 01 in the figure, the new
isolator has to be no. 01 and the old no. 01 has to be no. 02.

Short circuit / cut-off (break) on the COM loop

See chapter "COM loop units", page 37. See also EBL512 G3
Operating Instructions, chapter "Fault messages".

9.1.5

Units for Hazardous (Ex) areas

In hazardous (Ex) areas,

I

ntrinsically

S

afe (IS) and approved products

are required. The IS alarm points are connected to an interface outside
the Ex area.

Normally the analog addressable units (IS smoke and heat detectors)
shall be used, else conventional units (e.g. IS manual call point).

Conventional units are connected via a Galvanic isolator MTL 5061
(2820) to an expansion board 4580 Ex zone line input. See also
drawings 512 G3 – 33 and – 37.

Analog / addressable units are connected to a COM loop via an IS
barrier unit 2842. See also drawing 512 G3 – 31.

9.1.5.1

Galvanic isolators / IS barrier units

MTL5061

Galvanic isolator (2820). The isolator is used to connect

conventional  IS  detectors  and  manual  call  points  to  an
expansion  board  4580  zone  line  input  (programmed  in
"Resistor-Ex" mode).  The isolator has two zone line inputs and
two outputs (Channel 1 & 2) and it is mounted in a Waterproof
box  (IP66/67).    Four  compression  glands  for  the  cable  entries
and  an  end-of-line  resistor  (10K)  with  an  area  >230  mm

2

are

supplied. Box dimensions (L x W x H): 175 x 125 x 150 mm.
BASEEFA classification: EEx ia IIC T

amb

=60°C.

2842

Intrinsically safe (IS) barrier unit.

40

The barrier unit is used to

connect analog addressable IS detectors to a COM loop. The
unit has connectors for COM loop in / out, external power
supply (24 V DC, 60 mA) and one IS COM line for connection

40

This unit might still be under construction.

«
...
50
51
52
53
54
...
»

Summary of Contents for EBL512 G3 5000









































































































































































Reviews:

No comments

Related manuals for EBL512 G3 5000

Brand: D-Link Pages: 113

Brand: D-Link Pages: 146

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 168

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 29

Brand: Panasonic Pages: 37

Brand: Panasonic Pages: 9

Brand: Yudian Pages: 26

Brand: Veeder-Root Pages: 27

Brand: Valve Concepts Pages: 18

Brand: K&K Pages: 6

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Spartan-3A DSP FPGA Series

Brand: Xilinx Pages: 140

Brand: IDTECK Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands