Panasonic EBL512 G3 5000 Planning Manual Download Page 46 | Manualshive

Page: 46 / 168

background image

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

44

The Address setting tool (3314) is also used for mode setting:

NORMAL mode

: 4301 in this mode is in WinG3 set to one of

the six algorithms H-15,

H-35, L-15, L-35,

N-15

or N-35.

2330 mode

: Not used in system EBL512 G3.

2312 mode

: Not used in system EBL512 G3.

9.1.1.4

Conventional Detector Bases (CDB)

2324

Base. A conventional detector shall be plugged in 2324. Built-
in LED is lit to indicate that the detector plugged in the base has
activated fire alarm. Terminals for an ext. LED (2218).

9.1.1.5

Conventional Detectors

4318

Combination heat detector. Rate-of-rise

and

fixed temperature,

59°C, heat detector class

A1 R

. Static response temp. range 54-

65°C,

ambient temp. min./

typical

/max. -10/

+25

/+50°C

.

Shall be plugged in a conventional detector base (2324).

4350

Multi detector. 4350 is a smoke detector and a heat detector
within one housing. Scattered light (i.e. reflection of infrared
light) is used to detect

smoke

and the

heat

sensing element is a

thermistor. In order to secure the fire detection and to prevent
false (nuisance) alarms, an AI function is used, i.e.

a: combined heat and smoke sensing

b: variable delay function

c: adaptive learning function

See also chapter "Cyber sensor functions, page 121.

The detector has unleaded soldering.

Shall be plugged in a conventional detector base (2324).

4352

Photoelectric smoke detector.  Scattered light (i.e. reflection of
infrared  light)  is  used  to  detect  smoke.    An  advanced  alarm
algorithm is used to secure the smoke detection and to prevent
false  (nuisance)  alarms,  e.g.  a  minimum  of  nine  consecutive
readings  over  the  fire  alarm  level  are  required  before  the
detector goes into alarm. (One reading per sec.)
The detector has unleaded soldering.
Shall be plugged in a conventional detector base (2324).

4375

Heat detector. Fixed temperature heat detector, 60°C, class

A2S

(static response temp. range 54-70°C), latching.

Min./

typical

/max. ambient temp. -10/

+25

/+40°C.

The detector has unleaded soldering. Shall be plugged in a
conventional detector base (2324).

4376

Heat detector. Like 4375 but 80°C, class

BS

(static response

temp. range 69-85°C), latching.
Min./

typical

/max. ambient temp. -10/

+40

/+60°C.

The detector has unleaded soldering. Shall be plugged in a
conventional detector base (2324).

«
...
44
45
46
47
48
...
»

Summary of Contents for EBL512 G3 5000









































































































































































Reviews:

No comments

Related manuals for EBL512 G3 5000

Brand: Balboa Instruments Pages: 10

Brand: Quantum Data Pages: 36

medialon Showmaster Go

Brand: 7th Sense Pages: 2

Brand: HABONIM Pages: 9

Brand: Nedap Pages: 20

Brand: Talgil Pages: 14

Brand: Tadao Pages: 2

Brand: WAGNER Pages: 60

Brand: Aulisa Pages: 32

J1000 CIMR-JC series

Brand: YASKAWA Pages: 26

SAE 07.2 Series

Brand: AUMA Pages: 116

Brand: Multi-Clean Pages: 4

Brand: Primo Water Pages: 10

Brand: PENGWYN Pages: 32

Brand: Warner Electric Pages: 6

Brand: Sensitron Pages: 32

Brand: We Pages: 27

Brand: Paradox Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands