Panasonic EBL512 G3 5000 Planning Manual Download

Page: 117 / 168

Panasonic Electric Works Nordic AB

MEW01351

Rev: -

Planning Instructions Fire alarm system EBL512 G3, V1.1.x

115

The sounders will remain turned ON until they are turned OFF by
pressing the soft key "Evacuate off" (P7).

114

NOTE 1!

The alarm devices (sounders) will always be activated

steady (sound continuously) irrespective of the fact that the outputs
can be set to anything else for fire alarm (e.g. intermittent).

NOTE 2!

The text “Menu” above the soft key (P4) is visible in the

display only if the door in the c.i.e. is open, while the text "Evacuate" /
"Evacuate off" above (P7) is always visible in the current conventions.

16.31

WinG3 menu Tools

Figure 24. WinG3 menu "Tools". Some commands might be
disabled, see WinG3 help.

The WinG3 menu "Tools" is used, when the PC is connected to an
EBL512 G3 control unit for e.g. download / backup of SSD.

Validate

: The SSD is validated automatically before downloaded to

an EBL512 G3 but can also be done via this menu.

Log on control unit

: Log on / Log off to an EBL512 G3.

Synchronize

: (When connected and logged on to an EBL512 G3.)

Data (e.g. faults, disablements, etc.) will be synchronized, i.e. the
same in all control units and WinG3.

Download SSD

: (When connected and logged on to an EBL512 G3.)

For downloading of SSD to one or more EBL512 G3 control units and
connected Display Units (e.g. ext. FBP).

114

Alt. when the programmable input is de-activated.

Summary of Contents for EBL512 G3 5000









































































































































































Search results

Summary of Contents for EBL512 G3 5000

Reviews:

Related manuals for EBL512 G3 5000

Brands by name

Popular brands

Panasonic EBL512 G3 5000, Planning Manual

Search results

Summary of Contents for EBL512 G3 5000

Reviews:

Related manuals for EBL512 G3 5000

Brands by name

Popular brands