NetApp E2760 Installation Manual Download Page 9 | Manualshive

Page: 9 / 137

background image

Configuration

Options

•

Duplex E2712
controller-drive tray
with a HIC

•

Duplex E2724
controller-drive tray
with a HIC

Any combination of E2700 controller-drive trays attached to DE1600
drive trays, DE5600 drive trays, or DE6600 drive trays not to exceed a
maximum of 192 drive slots or 16 total trays in the storage array. You
can mix all three types of drive trays, or have the following number of
drive trays in a storage array:

•

15 DE1600 drive trays with an E2712

•

14 DE1600 drive trays with an E2724

•

Seven DE5600 drive trays

•

Three DE6600 drive trays with an E2712 controller-drive tray

•

Two DE6600 drive trays with an E2724 controller-drive tray

One of the following HICs (per controller):

•

Two or four 12-Gb/s SFF-8644 mini SAS-HD connectors

•

Two 10-Gb/s iSCSI RJ45 connectors

•

Two or four 10-Gb/s iSCSI SFP connectors

•

Two or four 16-Gb/s Fibre Channel SFP connectors

One 4-GB or one 8-GB DIMM memory for a maximum of 8-GB
capacity in each controller.

One 4-GB DIMM memory requires one 16-GB mSATA module for
controller cache backup in each controller. One 8-GB DIMM memory
requires two 16-GB mSATA modules for controller cache backup in
each controller.

Table 2: E2760 controller-drive tray options

Configuration

Options

Duplex E2760
controller-drive tray
with no HIC

Any combination of E2760 controller-drive trays attached to DE1600
drive trays, DE5600 drive trays, or DE6600 drive trays not to exceed a
maximum of 192 drive slots or 16 total trays in the storage array. You
can mix all three types of drive trays, or have the following number of
drive trays in a storage array:

•

11 DE1600 drive trays

•

Five DE5600 drive trays

•

Two DE6600 drive trays

One 4-GB or one 8-GB DIMM memory for a maximum of 8-GB
capacity in each controller.

One 4-GB DIMM memory requires one 16-GB mSATA module for
controller cache backup in each controller. One 8-GB DIMM memory
requires two 16-GB mSATA modules for controller cache backup in
each controller.

Step 1 - Preparing to install a controller-drive tray | 9

«
...
7
8
9
10
11
...
»

Summary of Contents for E2760










































































































































Reviews:

No comments

Related manuals for E2760

Brand: Medion Pages: 220

Brand: JBL Pages: 11

Brand: iTrak Pages: 6

ultratrak RM8000

Brand: Promise Technology Pages: 94

Brand: Pyle Pages: 12

Brand: Panasonic Pages: 100

Wireless music system for iPod

Brand: Brookstone Pages: 14

Brand: Power Dynamics Pages: 16

Brand: Plank Digital Audio Pages: 25

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 18

Brand: Panasonic Pages: 21

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands