NetApp E2760 Installation Manual Download Page 96

Page: 96 / 137

Note:

The three source wires on the DC power connector cable (–48 VDC) connect the

controller-drive tray to centralized DC power plant equipment, typically through a bus bar
located above the cabinet.

Note:

You do not have to connect the second DC power on each of the drive tray’s DC power-

fan canisters. The second DC power connection is for additional redundancy only and can be
connected to a second DC power bus.

5. Have a qualified service person connect the other end of the DC power connector cables to the

DC power plant equipment as follows:

a. Connect the brown –48 VDC supply wire to the negative terminal.

b. Connect the blue return wire to the positive terminal.

c. Connect the green/yellow ground wire to the ground terminal.

96 | E2700 Controller-Drive Tray and Related Drive Trays Installation Guide

Summary of Contents for E2760










































































































































Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands

NetApp E2760, Installation Manual

Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands