NetApp E2760 Installation Manual Download Page 4

Page: 4 / 137

Things to know - Host channels ................................................................................ 55

Procedure - Connecting host cables on a controller-drive tray ................................. 58

Step 6 - Installing the drive trays for the controller-drive tray

configurations ......................................................................................... 63

Things to know - General installation of drive trays ................................................. 63

Procedure - Installing the DE1600 and DE5600 drive trays ..................................... 63

Procedure - Installing drives in the DE1600 and DE5600 drive trays ...................... 71

Procedure - Installing the DE6600 drive tray ............................................................ 72

Procedure - Installing the drives in the DE6600 drive tray ....................................... 81

Things to know - Connecting the power cords .......................................................... 83

Procedure - Connecting the power cords .................................................................. 83

Step 7 - Connecting the controller-drive tray to the drive trays ............ 84

Key terms .................................................................................................................. 84

Drive channel ................................................................................................ 84

Things to know - E2700 controller-drive tray ........................................................... 84

Things to know - Drive trays ..................................................................................... 85

Things to know - Cabling configurations .................................................................. 86

Step 8 - Connecting the Ethernet cables ................................................... 91

Key terms .................................................................................................................. 91

In-band management ..................................................................................... 91

Out-of-band management .............................................................................. 91

Things to know - Connecting Ethernet cables ........................................................... 91

Procedure - Connecting Ethernet cables ................................................................... 92

Step 9 - Connecting the power cords ........................................................ 93

Things to know - AC power cords ............................................................................. 93

Things to know - DC power cords ............................................................................ 93

Procedure - Connecting AC power cords .................................................................. 94

Procedure - Connecting DC power cords .................................................................. 95

Step 10 - Turning on the power and checking for problems in a

controller-drive tray configuration ...................................................... 97

Procedure - Turning on the power to the storage array and checking for

problems in a controller-drive tray configuration ................................................ 97

Things to know - LEDs on the controller-drive tray ................................................. 98

Things to know - LEDs on the E2760 controller-drive tray .................................... 108

Things to know - General behavior of the LEDs on the controller-drive tray ........ 111

Things to know - Service Action Allowed LEDs .................................................... 114

Things to know - LEDs on the DE1600 and DE5600 drive trays ........................... 114

Things to know - LEDs on the DE6600 drive tray .................................................. 119

Things to know - LEDs on the DE6600 drive drawers ........................................... 123

Things to know - LEDs on the DE6600 drives ....................................................... 124

Things to know - General behavior of the LEDs on the drive trays ........................ 125

Things to know - Display sequence code definitions .............................................. 127

Things to know - Component failure identifications ............................................... 128

Things to know - Lock-down codes ........................................................................ 129

Things to know - Seven-segment display use cases ................................................ 131

4 | E2700 Controller-Drive Tray and Related Drive Trays Installation Guide

Summary of Contents for E2760










































































































































Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands

NetApp E2760, Installation Manual

Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands