NetApp E2760 Installation Manual Download Page 95

Page: 95 / 137

Procedure - Connecting DC power cords

About this task

Warning:

(W14) Risk of bodily injury – A qualified service person is required to make the DC

power connection according to NEC and CEC guidelines.

Important:

Make sure that you do not turn on the power to the controller-drive tray or the

connected drive trays until this documentation instructs you to do so.

Attention:

Before turning off any power switches on a DC-powered controller-drive tray, you must

disconnect the two-pole 20-amp circuit breaker.

Steps

1. Disconnect the two-pole 20-amp circuit breaker for the storage array.

2. Make sure that all of the DC power switches on the DC-powered controller-drive tray are turned

off.

•

Power switches on the E2712 or the E2724 controller-drive tray

Power switches

•

Power switches on the E2760 controller-drive tray

Power switches

3. Make sure that all of the DC power switches on the DC-powered drive trays are turned off.

4. Connect the DC power connector cables to the DC power connectors on the rear of the controller-

drive tray and the drive trays.

Step 9 - Connecting the power cords | 95

Summary of Contents for E2760










































































































































Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands

NetApp E2760, Installation Manual

Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands