NetApp E2760 Installation Manual Download Page 108

Page: 108 / 137

Table 16: LEDs on the power-fan canister

Location

LED

Color

Off

Standby Power

Green

The controller-drive tray
is in Standby mode, and
DC power is not
available.

The controller-drive tray
is not in Standby mode,
and DC power is
available.

Power-Fan DC
Power

Green

DC power from the
power-fan canister is
available.

DC power from the
power-fan canister is not
available.

Power-Fan
Service Action
Allowed

Blue

The power-fan canister
can be removed safely
from the controller-drive
tray.

The power-fan canister
cannot be removed safely
from the controller-drive
tray.

Power-Fan
Service Action
Required

Amber

A fault exists within the
power-fan canister.

Normal status.

Power-Fan AC
Power

Green

AC power to the power-
fan canister is present.

AC power to the power-
fan canister is not
present.

Things to know - LEDs on the E2760 controller-drive tray

The following sections provide information about the LEDs found on the E2760 controller-drive tray.

•

LEDs on the left bezel

108 | E2700 Controller-Drive Tray and Related Drive Trays Installation Guide

Summary of Contents for E2760










































































































































Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands

NetApp E2760, Installation Manual

Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands