NetApp E2760 Installation Manual Download Page 110

Page: 110 / 137

92025-01

Table 18: LEDs on the power canister

Location

LED

Color

Off

Standby Power

Green

The controller-drive
tray is in Standby
mode.

The controller-drive tray
is not in Standby mode.

Power DC Power

Green

DC power from the
power canister is
available.

DC power from the
power canister is not
available.

Power Service
Action Allowed

Blue

The power canister
can be removed safely
from the controller-
drive tray.

The power canister
cannot be removed safely
from the controller-drive
tray.

Power Service
Action Required

Amber

A fault exists within
the power canister.

Normal status.

Power AC Power

Green

AC power to the
power canister is
present.

AC power to the power
canister is not present.

•

LEDs on the fan canister

110 | E2700 Controller-Drive Tray and Related Drive Trays Installation Guide

Summary of Contents for E2760










































































































































Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands

NetApp E2760, Installation Manual

Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands