NetApp E2760 Installation Manual Download Page 119

Page: 119 / 137

Table 25: LEDs on AC power-fan canister

Location

LED

Color

Off

Standby
Power

Green

The drive tray is in
Standby mode, and DC
power is not available.

The drive tray is not in
Standby mode.

Power-Fan
DC Power

Green

DC power from the
power-fan canister is
available.

DC power from the
power-fan canister is not
available.

Power-Fan
Service
Action
Allowed

Blue

The power-fan canister
can be removed safely
from the drive tray.

The power-fan canister
cannot be removed safely
from the drive tray.

Power-Fan
Service
Action
Required

Amber

A fault exists within the
power-fan canister.

Normal status.

Power-Fan
AC Power

Green

AC power to the power-
fan canister is present.

AC power to the power-
fan canister is not
present.

Things to know - LEDs on the DE6600 drive tray

•

LEDs on the left bezel

Step 10 - Turning on the power and checking for problems in a controller-drive tray configuration | 119

Summary of Contents for E2760










































































































































Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands

NetApp E2760, Installation Manual

Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands