NetApp E2760 Installation Manual Download Page 115

Page: 115 / 137

Table 21: LEDs on the left end cap

Location

LED

Color

Off

Drive Tray Locate

White

Identifies a drive tray
that you are trying to
find.

Normal status.

Drive Tray Service
Action Required

Amber

A component within the
drive tray needs
attention.

Normal status.

Drive Tray Over-
Temperature

Amber

The temperature of the
drive tray has reached an
unsafe level.

Normal status.

Drive Tray Power

Green

Power is present.

Power is not
present.

Drive Tray Standby
Power

Green

The drive tray is in
Standby Power mode.

The drive tray is
not in Standby
Power mode.

•

LEDs on the drive

Step 10 - Turning on the power and checking for problems in a controller-drive tray configuration | 115

Summary of Contents for E2760










































































































































Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands

NetApp E2760, Installation Manual

Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands