NetApp E2760 Installation Manual Download Page 104

Page: 104 / 137

Table 14: LEDs on the controller canister – FC host interface card subplates*

Location

LED

Color

Off

Host Interface
Card Link 3 Up
LED 1

Green

The FC link has auto-
negotiated to 16-Gb/s if
both LEDs are on.

The FC link is
down if both
LEDs are off.

Host Interface
Card Link 3 Up
LED 0

Green

Host Interface
Card Link 4 Up
LED 1

Green

The FC link has auto-
negotiated to 16-Gb/s if
both LEDs are on.

The FC link is
down if both
LEDs are off.

Host Interface
Card Link 4 Up
LED 0

Green

Host Interface
Card Link 5 Up
LED 1

Green

The FC link has auto-
negotiated to 16-Gb/s if
both LEDs are on.

The FC link is
down if both
LEDs are off.

Host Interface
Card Link 5 Up
LED 0

Green

Host Interface
Card Link 6 Up
LED 1

Green

The FC link has auto-
negotiated to 16-Gb/s if
both LEDs are on.

The FC link is
down if both
LEDs are off.

Host Interface
Card Link 6 Up
LED 0

Green

104 | E2700 Controller-Drive Tray and Related Drive Trays Installation Guide

Summary of Contents for E2760










































































































































Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands

NetApp E2760, Installation Manual

Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands