NetApp E2760 Installation Manual Download Page 94

Page: 94 / 137

Procedure - Connecting AC power cords

Steps

1. Ensure that the circuit breakers in the cabinet are turned off.

2. Ensure that both of the power switches on the controller-drive tray are turned off.

•

Power switches on the E2712 and E2724 controller-drive trays

•

Power switches on the E2760 controller-drive tray

Power switches

3. Connect the primary power cords from the cabinet to the external power source.

4. Connect either a cabinet interconnect power cord, the power cords provided with the drive tray, or

the power cords specific to your particular cabinet to the AC power connector on each power
canister in the drive tray.

5. If you are installing other drive trays in the cabinet, connect a power cord to each power canister

in the drive trays.

94 | E2700 Controller-Drive Tray and Related Drive Trays Installation Guide

Summary of Contents for E2760










































































































































Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands

NetApp E2760, Installation Manual

Search results

Summary of Contents for E2760

Reviews:

Related manuals for E2760

Brands by name

Popular brands