manualshive.com logo in svg

MR TAPCON 230 AVT, Operating Instructions Manual

Share
Download
MR TAPCON 230 AVT Operating Instructions Manual Download Page 69

9 Operation

Maschinenfabrik Reinhausen GmbH 2021

69

7817454/02 EN

TAPCON

®

 230 Expert

When in delivery status, you can log in as the administrator as follows:

▪ User name: 

admin

▪ Password: 

admin

1. Go to 

Settings > Parameters > System > General > Service user ac-

cess activation

.

2. Select the desired option.

3. Press the 

Accept

 button to save the modified parameter.

4. Restart the device to adopt the change.

Service user access activation

You can use this parameter to activate or deactivate service user access.

9.1.2 Configuring the network

You can use this menu item to configure the necessary network interface.

You must wire the device in accordance with the respective control system
protocol [

►

Section 6.4.5, Page 47]. The following protocols are available:

▪ IEC 61850 Edition 2

▪ IEC 60870-5-101

▪ IEC 60870-5-104

▪ DNP3

▪ Modbus TCP

▪ Modbus RTU

1. Go to 

Settings > Parameters > System > Network settings

.

2. Select the desired parameter.

3. Set the parameter.

4. Press the 

Accept

 button to save the modified parameter.

IP address

You can use this  parameter to assign an IP address to the device.

Assign IP addresses to both web-based visualization and SCADA (optional)
in different subnets. Otherwise you will not be able to establish a connec-
tion.

Subnet mask

You can use this  parameter to set the subnet mask.

Summary of Contents for TAPCON 230 AVT







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands