manualshive.com logo in svg

MR TAPCON 230 AVT, Operating Instructions Manual

Share
Download
MR TAPCON 230 AVT Operating Instructions Manual Download Page 143

11 Fault elimination

Maschinenfabrik Reinhausen GmbH 2021

143

7817454/02 EN

TAPCON

®

 230 Expert

Characteristics/details

Cause

Remedy

Measured voltage

▪ Measured value too low

Voltage drop on the measuring
line.

Check the measured voltage.

Measured voltage

▪ Measured value fluctuates

Possible sources of interference:

▪ Cables laid in parallel.

▪ Tap-change operations.

Check the measured voltage.

Increase the distance from the source of inter-
ference.

Install a filter if necessary.

Measured current

▪ No measured value

Line to the current transformer in-
terrupted.

Check wiring.

Short-circuiting jumper in current
transformer is not removed.

Remove the short-circuiting jumper.

Measured current

▪ Measured value too high

▪ Measured value too low

Current transformer not correctly
parameterized.

Correct parameterization.

Table 52: Incorrect measured values

11.6 Parallel operation faults

Characteristics/details

Cause

Remedy

Problem with CAN bus.

▪ Device not listed.

Device incorrectly connected.

Check connections.

Connect as shown in connection diagram.

Devices have the same CAN bus
addresses.

Set different CAN bus addresses.

CAN bus address of device set to
"0".

Set CAN bus address (anything but 0).

Problem with parallel operation.

Different parallel operation meth-
ods set for devices in the parallel
operation group.

Check configuration.

Problem with master/follower par-
allel operation method.

More than 1 device is configured
as master in the parallel operation
group.

Check configuration.

No device configured as master
in the parallel operation group.

Check configuration.

Invalid tap position of master or
follower.

Check tap position.

Check wiring. Connect as shown in connection
diagram.

Summary of Contents for TAPCON 230 AVT







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands