manualshive.com logo in svg

MR TAPCON 230 AVT, Operating Instructions Manual

Share
Download
MR TAPCON 230 AVT Operating Instructions Manual Download Page 78

9 Operation

Maschinenfabrik Reinhausen GmbH 2021

78

7817454/02 EN

TAPCON

®

 230 Expert

Receiver IP address

You can use this parameter to set the IP address of the receiver.

Modbus address

You can use this parameter to set the Modbus address.

Serial interface

You can use this  parameter to select the serial interface for data transmis-
sion. You can select the following options:

▪ RS232

▪ RS485

Baud rate

You can use this parameter to set the serial interface's baud rate. You can
select the following options:

▪ 9600 baud

▪ 19200 baud

▪ 38400 baud

▪ 57600 baud

▪ 115200 baud

Parity

You can use this  parameter to set the parity. You can select the following
options:

▪ None

▪ Even

▪ Odd

Number of stop bits

You can use this  parameter to set the number of stop bits.

9.1.6.5 Configuring DNP3

If you would like to use the DNP3 control system protocol, you must set the
parameters listed below. Also refer to the section Configuring the network if
you want to use the DNP3 via TCP.

1. Go to 

Settings > Parameters > System > DNP3

.

2. Select the desired parameter.

3. Set the parameter.

4. Press the 

Accept

 button to save the modified parameter.

Summary of Contents for TAPCON 230 AVT







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands