manualshive.com logo in svg

MR TAPCON 230 AVT, Operating Instructions Manual

Share
Download
MR TAPCON 230 AVT Operating Instructions Manual Download Page 19

4 Product description

Maschinenfabrik Reinhausen GmbH 2021

19

7817454/02 EN

TAPCON

®

 230 Expert

4 Product description

4.1 Scope of delivery

Check the shipment for completeness based on the shipping documents.

▪ Voltage regulator

▪ RJ45 patch cables

▪ Shield clamps

▪ Plug connectors

▪ Tension clamps

▪ Technical documents

▪ Additional nameplate

▪ Terminating resistor for CAN bus

▪ Terminating resistor for RS485 bus

Optional

▪ Housing for wall mounting

▪ Device type-dependent:

– Ethernet to FO converter (SFP module)

– Serial to FO converter

4.2 Function description of the voltage regulation

The device keeps the output voltage of a transformer with an on-load tap-
changer constant.

The device compares the transformer's measured voltage (U

actual

) with a de-

fined reference voltage (U

desired

). The difference between U

actual

 and U

desired

 

is

the control deviation dU.

The device parameters can be adjusted to the line voltage behavior to
achieve a balanced control response with the on-load tap-changer only per-
forming a small number of tap-change operations.

Summary of Contents for TAPCON 230 AVT







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands