manualshive.com logo in svg

MR TAPCON 230 AVT, Operating Instructions Manual

Share
Download
MR TAPCON 230 AVT Operating Instructions Manual Download Page 72

9 Operation

Maschinenfabrik Reinhausen GmbH 2021

72

7817454/02 EN

TAPCON

®

 230 Expert

1. Go to 

Settings > Parameters > System > Screensaver

.

2. Select the desired parameter.

3. Set the parameter.

4. Press the 

Accept

 button to save the modified parameter.

Screensaver

If you activate this function, the device fully switches off the display when the
adjustable waiting period has expired if no key is pressed. The display
switches on again if you press any key.

Deactivating the screensaver has a negative impact on the service life of
the display. Maschinenfabrik Reinhausen recommends that you activate the
screensaver and set a waiting period of 15 minutes.

Screensaver waiting time

You can use this parameter to set the screensaver waiting time.

Dimming

When you activate this function, the device reduces the brightness of the
display when the adjustable waiting time has expired if no key is pressed.
The device then switches back to full brightness when you subsequently
press any key.

If the screensaver and brightness dimming are activated, you have to press
any key twice in order to reactivate the display at full brightness.

Dimming waiting time

You can use this parameter to set the dimming waiting time.

Brightness dimming

Setting for the brightness when the display is dimmed. 100% corresponds to
full brightness, 10% to the lowest brightness.

9.1.5 Configuring syslog

The device supports the transmission of log messages via the syslog proto-
col in accordance with the standards RFC 5424 and RFC 3164.

1. Go to 

Settings > Parameters > System > Syslog

.

2. Select the desired parameter.

3. Set the parameter.

4. Press the 

Accept

 button to save the modified parameter.

Summary of Contents for TAPCON 230 AVT







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands