manualshive.com logo in svg

MR TAPCON 230 AVT, Operating Instructions Manual

Share
Download
MR TAPCON 230 AVT Operating Instructions Manual Download Page 83

9 Operation

Maschinenfabrik Reinhausen GmbH 2021

83

7817454/02 EN

TAPCON

®

 230 Expert

9.1.7.3 Linking status messages

You can link each event with a status message. The device provides 10
generic status messages for this purpose. When you link a message to an
event, the device sets the data point to "On" when the event occurs. When
the event stops, the device sets the data point to "Off". A parameter is avail-
able for each available SCADA message.

To forward control system commands, you need to link the control system
messages to the 

General purpose input

 or 

Generic SCADA command

events.

ü

The desired event number is known [

►

Section 9.1.10, Page 87].

1. Go to 

Settings > Parameters > System > Link messages

.

2. Select the desired parameter.

3. Enter the desired event number.

4. Press the 

Accept

 button to save the modified parameter.

Generic status message X

You can use this parameter to link the SCADA message with an event mes-
sage. To do so, enter the desired event number.

If you enter event number 500, the link is disabled.

9.1.8 Configuring analog inputs

You can flexibly configure the device's analog inputs  and assign device
functions.

The device supports analog sensors with linear characteristic curves and
only outputs analog signals with linear characteristic curves.

Summary of Contents for TAPCON 230 AVT







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands