manualshive.com logo in svg

MR TAPCON 230 AVT, Operating Instructions Manual

Share
Download
MR TAPCON 230 AVT Operating Instructions Manual Download Page 71

9 Operation

Maschinenfabrik Reinhausen GmbH 2021

71

7817454/02 EN

TAPCON

®

 230 Expert

Time synchronization via SNTP

You can use this parameter to activate time synchronization using an SNTP
time server.

SNTP time server

You can use this parameter to enter the IP address of a SNTP time server. If
you are using a time server, the device uses the time of the time server as
the system time.

Be sure to enter a valid time server address that is not 0.0.0.0, otherwise it
will not be possible to connect to the device.

Synchronization interval

You can use this parameter to set the interval at which the device is to call
up the time from the time server.

Time zone

To adjust the device time to your local time, you can use the time shift  pa-
rameter to set the time shift to UTC.

Example:

Region

Time shift to UTC

Mumbai, India

UTC +5:30 h

Beijing, China

UTC +8:00 h

Brasilia, Brazil

UTC -3:00 h

Table 15: Time shift to UTC (Coordinated Universal Time)

Time

You can use this parameter to set the date and time manually.

SNTP time server 2

You can use this parameter to enter the IP address of the second time
server (optional).

9.1.4 Setting the screensaver

To increase the service life of the display on the front panel of the device,
you can activate and set a screensaver. The following functions are avail-
able for this purpose:

▪ Switching off the display

▪ Dimming the brightness of the display

Summary of Contents for TAPCON 230 AVT







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands