manualshive.com logo in svg

MR TAPCON 230 AVT, Operating Instructions Manual

Share
Download
MR TAPCON 230 AVT Operating Instructions Manual Download Page 41

6 Mounting

Maschinenfabrik Reinhausen GmbH 2021

41

7817454/02 EN

TAPCON

®

 230 Expert

Excessive line capacitance can prevent the relay contacts from interrupting
the contact current. In control circuits operated with alternating current, take
into account the effect of the line capacitance of long control cables on the
function of the relay contacts.

If you want to route Ethernet connections from a control cabinet or building,
we recommend using fiber-optic cables (in accordance with the
IEC 61850-90-4 recommendation).

Cable

Interface

Cable type

Conductor cross-sec-

tion

Max. length

Power supply (external)

X9

Unshielded

1.5 mm²

Voltage measurement

UI-X7

Shielded

Current measurement

UI-X7

Unshielded

2.5 mm²

Digital signal inputs

DI 16

Shielded

4 mm²

400 m (<25 Ω/km)

Digital signal outputs

DO 8

Shielded

1.5 mm²

Analog signal inputs

AI 4

Shielded

1 mm²

400 m (<25 Ω/km)

RS232, D-SUB 9-pole

COM X3

Shielded

0.25 mm²

25 m

RS485

COM-X6

Shielded

0.25 mm²

140 m

CAN bus

COM-X6

Shielded

0.75 mm²

2000 m (total CAN bus)

Ethernet RJ45

X2, X3

Min. CAT5, shielded

S/FTP

100 m

Ethernet FO

COM X4

Duplex LC multi-

mode, Om3, 1310 nm

2000 m

110 V DC output

X8

Unshielded

1.5 mm²

RJ45 patch cables

Min. CAT5, shielded

S/FTP

approx. 30 cm

Table 10: Recommendation for connection cables

*) Observe line capacitance, see note above.

6.4.2 Electromagnetic compatibility

The device has been developed in accordance with applicable EMC stan-
dards. The following points must be noted in order to maintain the EMC
standards.

6.4.2.1 Wiring requirement of installation site

Note the following when selecting the installation site:

▪ The system's overvoltage protection must be effective.

▪ The system's ground connection must comply with all technical regula-

tions.

Summary of Contents for TAPCON 230 AVT







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands