manualshive.com logo in svg

MR TAPCON 230 AVT, Operating Instructions Manual

Share
Download
MR TAPCON 230 AVT Operating Instructions Manual Download Page 110

9 Operation

Maschinenfabrik Reinhausen GmbH 2021

110

7817454/02 EN

TAPCON

®

 230 Expert

1. Go to 

Settings > Parameters > On-load tap-changer > Voltage regula-

tion > Change remote desired value setting

.

2. Select the desired option in the list.

3. Press the 

Accept

 button to save the modified parameter.

Selecting a desired value

You can use this parameter to select the desired value used for control. You
can choose between desired value 1, desired value 2 and desired value 3.

ü

Type of remote desired value setting [

►

Page 109] selected.

1. Go to 

Settings > Parameters > On-load tap-changer > Voltage regula-

tion > Desired value

.

2. Select the desired value from the list.

3. Press the 

Accept

 button to save the modified parameter.

9.3.1.1.1 Analog setting of the desired value

With the analog setting of the desired value, the desired value for the auto-
matic voltage regulation can be variably adapted using an analog signal (e.g.
4...20 mA).

Max.

Min.

Desired value

Max.

Min.

Analog signal

Figure 48: Analog setting of the desired value

In order to configure the analog setting of the desired value, you can set the
parameters as described below.

To specify the desired value using an analog signal, you need to create a
signal at the 

Desired value setting release

 input. If this is not done, the de-

vice uses the set desired value 1.

You have to set the parameters for both winding 1 (W1) and winding 2
(W2).

Summary of Contents for TAPCON 230 AVT







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands