manualshive.com logo in svg

MR TAPCON 230 AVT, Operating Instructions Manual

Share
Download
MR TAPCON 230 AVT Operating Instructions Manual Download Page 129

9 Operation

Maschinenfabrik Reinhausen GmbH 2021

129

7817454/02 EN

TAPCON

®

 230 Expert

You can select the following options:

Option

Description

Independent regula-
tion

The device switches from parallel operation to normal auto-
matic voltage regulation

Auto blocking

Automatic voltage regulation is blocked.

cosφ interpolation

Continuation of parallel operation with interpolated values
(only possible with circulating reactive current parallel oper-
ation method)

Power factor

Circulating reactive current minimization without CAN bus
communication parallel operation method

Table 44: Behavior if no communication present

9.3.3.2.11 Setting delay time for parallel operation error messages

You can use this parameter to set the delay time for a parallel operation er-
ror message so that brief fault messages are not received if the motor-drive
units involved in the parallel operation have different runtimes.

9.3.3.3 Parallel operation

In the parallel operation menu, you can display information about the de-
vices that are connected by CAN bus.

Description

Parallel operation status:

▪ Gray = Independent mode

▪ Blue = Parallel operation is active

▪ Red = Parallel operation error

CAN addr.

CAN bus address

Grp.

Parallel operation group

Method

Active parallel operation method

Current tap position

U [V]

Voltage

I_p [%]

Active current

I_q [%]

Reactive current

Blocking:

▪ Gray: Parallel operation not blocked

▪ Red: Parallel operation blocked

Table 45: Information about parallel operation

► Go to 

Information > Parallel operation

.

Summary of Contents for TAPCON 230 AVT







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands