manualshive.com logo in svg

MR TAPCON 230 AVT, Operating Instructions Manual

Share
Download
MR TAPCON 230 AVT Operating Instructions Manual Download Page 22

4 Product description

Maschinenfabrik Reinhausen GmbH 2021

22

7817454/02 EN

TAPCON

®

 230 Expert

Remote mode (REMOTE)

In remote mode, you can make entries and issue commands using digital in-
puts.

AVR AUTO

AVR MANUAL

LOCAL

REMOTE

LOCAL

REMOTE

Automatic regulation

Yes

Yes

No

No

Tap-change operation via
operating controls

No

No

Yes

No

Tap-change operation via
inputs

No

No

No

Yes

Tap-change operation via
SCADA

1)

No

No

No

Yes

Value adjustment via
SCADA

1)

No

Yes

No

Yes

Table 7: Overview of operating modes

1)

 Only with the TAPCON® 230 expert and TAPCON® 230 AVT versions

4.5 Design

4.5.1 Display, operating elements and front interface

Figure 3: Voltage regulator

1 REMOTE key

2)

Activate REMOTE mode

2 AUTO key

Activate AUTO mode

3 RAISE key

Send a control command to the motor-
drive unit to increase the voltage.

1)

4 MANUAL key

Activate MANUAL mode

5 LOWER key

Send a control command to the motor-
drive unit to reduce the voltage.

1)

6 Display

-

7 Front interface

RJ45 Ethernet interface

Summary of Contents for TAPCON 230 AVT







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands