manualshive.com logo in svg

MR TAPCON 230 AVT, Operating Instructions Manual

Share
Download
MR TAPCON 230 AVT Operating Instructions Manual Download Page 79

9 Operation

Maschinenfabrik Reinhausen GmbH 2021

79

7817454/02 EN

TAPCON

®

 230 Expert

9.1.6.5.1 DNP3 transmission type

You can use this parameter to set the transmission type. You can select the
following options:

▪ TCP

▪ Serial

Serial interface

You can use this  parameter to select the serial interface for data transmis-
sion. You can select the following options:

▪ RS232

▪ RS485

Baud rate

You can use this parameter to set the serial interface's baud rate. You can
select the following options:

▪ 9600 baud

▪ 19200 baud

▪ 38400 baud

▪ 57600 baud

▪ 115200 baud

TCP port

You can use this parameter to set the TCP port.

Receiver IP address

You can use this parameter to set the IP address of the receiver.

Parity

You can use this  parameter to set the parity. You can select the following
options:

▪ None

▪ Even

▪ Odd

Number of stop bits

You can use this  parameter to set the number of stop bits.

Device address

You can use this parameter to set the device link address.

Summary of Contents for TAPCON 230 AVT







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands