manualshive.com logo in svg

MR TAPCON 230 AVT, Operating Instructions Manual

Share
Download
MR TAPCON 230 AVT Operating Instructions Manual Download Page 47

6 Mounting

Maschinenfabrik Reinhausen GmbH 2021

47

7817454/02 EN

TAPCON

®

 230 Expert

6.4.5 Connecting SCADA

NOTICE

Damage to the device!

Using the wrong data cable may damage the device.

► Only use data cables which comply with the description below.

Depending on the control system used, you have to connect the device with
one of the following versions.

6.4.5.1 Serial interface RS485 (COM-X6)

1. Connect the wires of the shielded cable in pins 7 (Data +), 6 (GND) and 5

(Data-) of the COM-X6 connector.

Figure 29: Connecting wires in pins 7, 6, 5

2. Position the cable shielding, screw it into the shield clamp provided, and

provide strain relief (using a cable tie).

Figure 30: Shield clamp and strain relief

3. Connect the COM-X1 RJ45 interface and the CPU-X4 interface together

using the patch cable.

Summary of Contents for TAPCON 230 AVT







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands