manualshive.com logo in svg

Motorola PTP 300 Series, User Manual, Page: 86 / 288

Share
Download
Motorola PTP 300 Series User Manual Download Page 86

  

6 

Installation 

 

66

 

6.6  Establishing a Radio Link 

The following is a description of the steps taken to establish a radio link between the two  

units forming the bridge and align the units for the best signal strength.  

6.6.1  Aligning the PTP 300 Series Bridge ODUs  

The PTP 300 Series Bridge uses audible tones during installation to assist the installer with 

alignment. The installer should adjust the alignment of the ODU in both azimuth and elevation 

until highest pitch tone is achieved

.

  

The pitch of the alignment tone is proportional to the received power of the wireless signals. 

The best results are usually achieved by making small incremental movement in angular 

alignment. 

The tones and their meanings are as follows:  

Table 7 - Audio indications from the ODU 

State Name  

Tone 
Description  

State Description  

Pitch Indication (Higher 
pitch = higher power) 

Free Channel 
Search 

Regular beep  Executing band scan 

N/A 

Scanning Slow 

broken 

tone 

Not demodulating the wanted 
signal 

Rx Power 

Synchronized Fast 

broken 

tone 

Demodulating the wanted 
signal 

Rx Power 

Registered 

Solid tone 

Both Master and Slave units 
exchanging Radio layer MAC 
management messages 

Rx Power 

Alarm Fast 

broken 

dual tone 

A fatal error has occurred. 

 

 

The term ‘wanted signal’ refers to that of the peer unit being installed. 

4Gon   www.4Gon.co.uk   [email protected]   Tel: +44 (0)1245 808195   Fax: +44 (0)1245 808299 

Summary of Contents for PTP 300 Series

































































































































































































































































































Reviews:

No comments