Motorola PTP 300 Series User Manual Download Page 199

Page: 199 / 288

10 Connectorized PTP 300 Series Bridge

179

10.5.1 Cable Losses (FCC Regions Only)

The FCC approval for the product is based on tests with a cable loss between the units of not

less than 1.2 dB at 5.8 GHz. The use of lower cable losses would result in the installation

being outside the FCC rules. As an indication, 1.2 dB of cable loss corresponds to the

following cable lengths, excluding connector losses (source: Times Microwave).

Table 17 - Cable Losses per Length

Length for 1.2dB Cable Loss at 5.8 GHz

Cable

(ft)

(m)

LMR100 1.9

0.6

LMR200 4.6

1.4

LMR300 7.25

2.2

LMR400 11.1

3.4

LMR600 16.5

5.0

10.6 Antenna Choices

The main selection criterion is the required antenna gain. The secondary criterion is the ease

of mounting and alignment. For example, the Radio Waves Parabolic dishes are supplied with

a mount that allows adjustment for alignment independent of the actual antenna mounting.

This type of antenna is much easier to align than those that have to be rotated around the

mounting pole for alignment.

In non-FCC regions, antenna choice is not restricted, but any region specific EIRP limit must

be obeyed by reducing the maximum Transmit power, see Section 4.2 “Licenses and Region

Codes”.

In FCC regions, antenna choice is restricted as described in Sections 16.2.8 “PTP 54300

FCC Antenna Restrictions” and 16.3.8 “PTP 58300 FCC Antenna Restrictions”.

The maximum permitted antenna gain depends upon product variant as follows:

•

PTP 58300: 37.7 dB

•

PTP 54300: 34.9 dB

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Summary of Contents for PTP 300 Series

































































































































































































































































































Search results

Summary of Contents for PTP 300 Series

Reviews:

Motorola PTP 300 Series, User Manual, Page: 199 / 288

Search results

Summary of Contents for PTP 300 Series

Reviews: