Motorola PTP 300 Series User Manual Download Page 223

Page: 223 / 288

13 AES Encryption

203

6. Reboot both ends of the link Figure 124. The software is designed to allow five

seconds so that a user can command both ends of the link to reboot before the

wireless link drops.

Figure 124 - Configuration Reboot Screen

13.4 Wireless Link Encryption FAQ

13.4.1 Encryption data entry fields are not available

Check that the correct license key has been inserted into the unit. The current license key is

displayed on the ‘License Key’ data entry page.

13.4.2 Link fails to bridge packets after enabling link encryption

If the wireless link status on the status web page indicates that the link is ‘Searching’, and you

can browse to the local end of the link but not to the remote end, then check that the same

encryption algorithm and key have been entered at both ends of the link. Failure to enter the

same algorithm and key will result in received packets not being decrypted correctly.

13.4.3 Loss of AES following downgrade

When downgrading (using Recovery software image 05-01 onwards) to an earlier version of

software that does not support AES, the unit will indicate that the region code is invalid. The

user will be required to re-install correct software (supplied when AES key was activated) and

reboot the unit.

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Summary of Contents for PTP 300 Series

































































































































































































































































































Search results

Summary of Contents for PTP 300 Series

Reviews:

Motorola PTP 300 Series, User Manual, Page: 223 / 288

Search results

Summary of Contents for PTP 300 Series

Reviews: