Motorola PTP 300 Series User Manual Download Page 177

Page: 177 / 288

8 Recovery Mode

157

8.3 Reset IP & Ethernet Configuration

To reset IP & Ethernet configuration back to factory defaults the user should press the “Reset

IP & Ethernet Configuration back to factory defaults” button on the “Recovery Options” page

(

Figure 92). The user will now be presented with a pop up box asking them to confirm the

action (Figure 96).

Figure 96 - Confirm Reset to Factory Default Pop Up

On confirmation the following page will be displayed (Figure 97). The user should now reboot

the unit by pressing the “Reboot” button.

Figure 97 - IP and Ethernet Erased Successfully page

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Summary of Contents for PTP 300 Series

































































































































































































































































































Search results

Summary of Contents for PTP 300 Series

Reviews:

Motorola PTP 300 Series, User Manual, Page: 177 / 288

Search results

Summary of Contents for PTP 300 Series

Reviews: