manualshive.com logo in svg

Motorola PTP 300 Series, User Manual, Page: 192 / 288

Share
Download
Motorola PTP 300 Series User Manual Download Page 192

 

 

10 Connectorized PTP 300 Series Bridge 

 

172

10 Connectorized PTP 300 Series Bridge 

This section details the changes and additional features relevant to the connectorized version 

of the PTP 300 Series products. 

The following topics are described in this section: 

•

 

10.1 Product Description 

•

 

10.2 Software/Features 

•

 

10.3 Deployment Considerations 

•

 

10.4 Link Budget 

•

 

10.5 Regulatory Issues with Connectorized Units 

•

 

10.6 Antenna Choices 

•

 

10.7 Installation 

•

 

10.8 Additional Lightning Protection 

10.1  Product Description 

10.1.1 Hardware 

The Connectorized PTP 300 Series Bridge is a variant designed to provide the system 

integrator and installer with the ability to provide extra capability to cope with very difficult 

radio links compared to the PTP 300 Series Integrated model.  The variant allows the use of a 

variety of externally mounted antennas, either Flat Plate or Dish, which have higher gains 

than provided by the integrated antenna that is normally used. 

Figure 107 – Connectorized PTP 300 Series Bridge Outdoor Unit 

 

4Gon   www.4Gon.co.uk   [email protected]   Tel: +44 (0)1245 808195   Fax: +44 (0)1245 808299 

Summary of Contents for PTP 300 Series

































































































































































































































































































Reviews:

No comments