manualshive.com logo in svg

Motorola PTP 300 Series, User Manual, Page: 236 / 288

Share
Download
Motorola PTP 300 Series User Manual Download Page 236

 

 

16 PTP 300 Reference Information 

 

216

16 PTP 300 Reference Information 

This section describes the reference information and regulatory notices that are common to 

all PTP 300 products and those that are specific to each frequency variant. 

The following topics are described in this section: 

•

 

16.1 PTP 300 General Reference Information 

•

 

16.2 PTP 54300 Reference Information 

•

 

16.3 PTP 58300 Reference Information 

 

16.1  PTP 300 General Reference Information  

16.1.1 PTP 300 System Specifications 

Table 22 – PTP 300 Management Specifications 

Management 

 

Specification 

Status Indication  

Power status 
Ethernet Link Status 
Data activity 

Installation  

Web server and browser for setup. 
Audio tone feedback during installation , plus 
graphical installation tool suitable for laptop and 
PDA computing devices. 
Web server for confirmation. 

Radio Performance and Management 

Via web server and browser, SNMP  

Alarms  

Via configurable email alerts, SNMP 

System Management 

Web or SNMP v1/v2c using MIBII, WiMAX MIB, 
and a proprietary PTP MIB; Canopy Prizm. 

Lightning protection 

Built into the ODU; an external PTP Lightning 
Protection Unit (PTP-LPU) end device is required 
near the base of the tower or wall at the cable 
entrance point leading to the network. 

 

4Gon   www.4Gon.co.uk   [email protected]   Tel: +44 (0)1245 808195   Fax: +44 (0)1245 808299 

Summary of Contents for PTP 300 Series

































































































































































































































































































Reviews:

No comments