manualshive.com logo in svg

Motorola PTP 300 Series, User Manual, Page: 195 / 288

Share
Download
Motorola PTP 300 Series User Manual Download Page 195

 

 

10 Connectorized PTP 300 Series Bridge 

 

175

10.2.3 Installation Pages 

The installer is prompted to enter the Antenna Gain and Cable Loss (Connectorized PTP 300 

Series Bridge to antenna) at each end of the link.  The Installation Pages for the 

connectorized version are shown as Figure 110 to Figure 112. 

Figure 110 - Connectorized PTP 300 Series Bridge ‘Installation Wizard’ Page 

 

Antenna Gain 

Gain of the antenna you are connecting to the unit, see Section 10.6 “Antenna Choices”. 

Cable Loss 

Loss in the cable between the ODU and the antenna.  

 

NOTE

 

If there is a significant difference in length of the antenna cables for the two antenna 
ports, then the average value should be entered. 

 

4Gon   www.4Gon.co.uk   [email protected]   Tel: +44 (0)1245 808195   Fax: +44 (0)1245 808299 

Summary of Contents for PTP 300 Series

































































































































































































































































































Reviews:

No comments