manualshive.com logo in svg

Motorola PTP 300 Series, User Manual, Page: 167 / 288

Share
Download
Motorola PTP 300 Series User Manual Download Page 167

 

 

7 Web Page Reference 

 

147

The trace selection allows the user to control which traces are plotted. 

As with other management pages the page refresh period can be used to interactively 

monitor the wireless link. 

7.11.2 CSV Download 

The diagnostics Download page allows the system administrator to download snapshots of 

system diagnostics. 

Figure 83 - CSV Download 

 

The following diagnostics are available: 

•

 Vector 

Error 

•

 Rx 

Power 

•

 Tx 

Power 

•

 

Signal Strength Ratio V/H 

•

 Link 

Loss 

•

 

Rx Data Rate 

•

 

Tx Data Rate 

•

 

Aggregate Data Rate 

•

 Receive 

SNR 

•

 Rx 

Gain 

All diagnostics are extracted from the associated status and statistics web page histograms. 

They are translated in a CSV file containing at most 5784 entries. These 5784 entries 

comprise 3600 entries for the first hour, 1440 entries for the next 24 hours and 744 entries for 

the next 31 days. 

4Gon   www.4Gon.co.uk   [email protected]   Tel: +44 (0)1245 808195   Fax: +44 (0)1245 808299 

Summary of Contents for PTP 300 Series

































































































































































































































































































Reviews:

No comments