Motorola PTP 300 Series User Manual Download Page 179

Page: 179 / 288

8 Recovery Mode

159

On confirmation the following page will be displayed (Figure 100). The user should now

reboot the unit by pressing the “Reboot” button.

Figure 100 - Erase Configuration Successful Page

The user will now be presented with a pop up box asking them to confirm the action (Figure

101)

Figure 101 – Erase Configuration - Reboot Confirmation Pop Up

The unit will now reboot. The unit should now start up in normal mode but with all

configuration erased. Should the unit fail to start up the user should refer to Section 9 “ (Fault

Finding”.

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Summary of Contents for PTP 300 Series

































































































































































































































































































Search results

Summary of Contents for PTP 300 Series

Reviews:

Motorola PTP 300 Series, User Manual, Page: 179 / 288

Search results

Summary of Contents for PTP 300 Series

Reviews: