manualshive.com logo in svg

Motorola PTP 300 Series, User Manual, Page: 120 / 288

Share
Download
Motorola PTP 300 Series User Manual Download Page 120

 

 

7 Web Page Reference 

 

100

Ethernet Tx Packets 

This displays the total number of good packets the bridge has sent for transmission by the 
local Ethernet interface.  

Ethernet Rx Packets 

This displays the total number of good packets the bridge has received from the local 
Ethernet interface.  

Packets To Internal Stack 

This displays the total number of good packets the bridge has transmitted to the internal stack 
(for example, ARP requests, PING requests, HTTP requests).  

Packets From Internal Stack 

This displays the total number of good packets the bridge has received from the internal stack 
(for example ARP responses, PING replies, HTTP responses).  

Link Symmetry 

Link Symmetry: A ratio that expresses the division between transmit and receive time in the 
TDD frame. The first number in the ratio represents the time allowed for the transmit direction 
and the second number represents the time allowed for the receive direction. 

Line Of Sight Mode 

The current setting of the Line Of Sight Mode control, either Enabled or Disabled. 

This is 

hidden unless the line of sight capability is enabled by license key.

 

 

 

Transmit Data Rate 

The data rate in the transmit direction, expressed in Mbps and presented as: max, mean, min, 
and latest in an histogram format. The max, min and latest are true instantaneous 
measurements; the mean is the mean of a set of one second means. See Section 7.3.1 
“Histogram Data”. Expected data rates can be found in Section 12 “Data Rate Calculations”.  

Receive Data Rate 

The data rate in the receive direction, expressed in Mbps and presented as: max, mean, min, 
and latest in an histogram format. The max, min and latest are true instantaneous 
measurements; the mean is the mean of a set of one second means. See Section 7.3.1 
“Histogram Data”. Expected data rates can be found in Section 12 “Data Rate Calculations”.  

Aggregate Data Rate 

The sum of the data rate in the directions expressed in Mbps and presented as: max, mean, 
min, and latest in an histogram format. The max, min and latest are true instantaneous 
measurements; the mean is the mean of a set of one second means. See Section 7.3.1 
“Histogram Data”. Expected data rates can be found in Section 12 “Data Rate Calculations”. 

Link Capacity 

The maximum aggregate data capacity available for user traffic under the current radio link 
conditions, assuming the units have been connected using Gigabit Ethernet. The sum of the 
displayed Transmit and Receive data rates may be lower than this figure if the link isn't fully 
loaded by the current traffic profile. 

4Gon   www.4Gon.co.uk   [email protected]   Tel: +44 (0)1245 808195   Fax: +44 (0)1245 808299 

Summary of Contents for PTP 300 Series

































































































































































































































































































Reviews:

No comments