Home
/
Motorola
/
PTP 300 Series
/
User Manual

Motorola PTP 300 Series, User Manual, Page: 196 / 288

Share

Page: 196 / 288

Motorola PTP 300 Series User Manual Download Page 196

10 Connectorized PTP 300 Series Bridge

176

Spectrum Management Control

Is used to configure the PTP 300 Series Bridge Spectrum Management features, see Section
7.9 “Spectrum Management” for more details. i-DFS is the abbreviation for intelligent
Dynamic Frequency Selection, which continually monitors the spectrum looking for the
channel with the lowest level of on channel and co-channel interference. Fixed frequency
mode allows the installer to fix the Transmit and receive frequencies on the units. The
frequencies may be configured symmetrically or asymmetrically.

Figure 111 - Connectorized PTP 300 Series bridge ‘Confirm Installation’ Page

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

«
...
194
195
196
197
198
...
»

Summary of Contents for PTP 300 Series

































































































































































































































































































Reviews:

No comments