Motorola PTP 300 Series User Manual Download Page 238

Page: 238 / 288

16 PTP 300 Reference Information

218

Table 25 – PTP 300 Power Supply Specifications

Power Supply

Separate power supply unit (included)

Dimensions

Width 9.75” (250mm), Height 1.5” (40mm), Depth 3” (80mm)

Weight

1.9 lbs (0.864 Kg)

Power source

90 – 264 V ac, 50 – 60 Hz / 36 – 60 V dc

Power consumption 55 W max

16.1.2 PTP 300 Safety Compliance

Table 26 – PTP 300 Safety Compliance Specifications

Region

Specification

USA UL

60950

Canada CSA

C22.2

No.60950

International CB

certified

& certificate to IEC 60950

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Summary of Contents for PTP 300 Series

































































































































































































































































































Search results

Summary of Contents for PTP 300 Series

Reviews:

Motorola PTP 300 Series, User Manual, Page: 238 / 288

Search results

Summary of Contents for PTP 300 Series

Reviews: