Home
/
Motorola
/
PTP 300 Series
/
User Manual

Motorola PTP 300 Series, User Manual, Page: 266 / 288

Share

Page: 266 / 288

Motorola PTP 300 Series User Manual Download Page 266

16 PTP 300 Reference Information

246

16.3.4 PTP 58300 Radio System Specifications

Table 43 contains radio system specifications for the PTP 58300.

Table 43 - PTP 58300 RF Specifications

Radio Technology

Specification

RF Band

5.725-5.875 GHz

Channel Selection

By intelligent Dynamic Frequency Selection (i-DFS) or
manual intervention

Automatic detection on start-up and continual adaptation to

avoid interference.

Channel size

5, 10 and 15 MHz

Transmit Power

Varies with modulation mode and settings from -18 dBm to
27 dBm.

Modulation

Dynamic; adapting between BPSK single and 64 QAM.

Receiver Noise Figure

Typically 6 dB

Antenna Type

Integrated: Flat plate antenna. Connectorized: Approved to
operate with a selection of separately-purchased single and
dual polar antennas through 2xN-type connectors (check
local regulations prior to purchase).

Antenna Gain

23 dBi typical

Antenna Beamwidth

8 Degrees

Receiver Sensitivity

Adaptive, varying between -94 dBm and -69 dBm.

Duplex Scheme

Symmetric fixed, asymmetric fixed or adaptive TDD; same
or split frequency Tx/Rx where regulations permit.

Range

155 miles (250 km)

Security and Encryption

Proprietary scrambling mechanism. Optional FIPS-197
compliant 128- and 256-bit AES Encryption.

Weather Sensitivity

Sensitivity at higher modes may be reduced during high
winds through trees due to Adaptive Modulation Threshold
changes

Error Correction

FEC

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

«
...
264
265
266
267
268
...
»

Summary of Contents for PTP 300 Series

































































































































































































































































































Reviews:

No comments